How to Install Hardwood Floor Panels With the Nail Down Method

There are a variety of methods for installing hardwood flooring. The nail down method of laying hardwood floors has become remarkably common. For those learning how to install hardwood flooring, there is no easier or straightforward technique compared to nail technique.

Unlike other methods which essentially need you to be an amateur carpenter or even a professional carpenter, the nail down method on how best to install hardwood flooring Toronto can be accomplished by anyone who will swing a hammer. Well, that’s not all it takes. Additionally, you need to be willing to read the safety instructions that come with the tools you’ll be using.

Tools You’ll Need as Your Learn How to Install Hardwood Floor Panels

Carpenter’s Crayon – Use this to create guidelines in your sub floor. You will also want it to draw lines where you’re reduce your hardwood panels.

Claw Hammer – Any regions near barriers or walls in which you can not get enough space to swing a rubber mallet is going to need to be reached with your claw hammer.

Cutter Knife – Use this often because of unexpected actions involved as you understand how to install hardwood flooring. Nevertheless, the main purpose of this device is going to be to cut any surplus wood when alterations of just a millimeter or two have to be made.

Electric Drill and 3/32″ Drill Bit – Use this to drill your pilot holes, which should be slightly smaller in length and circumference than your nails.

Hardwood Flooring Nails (2″) – These nails are important because they will be exactly what hold your flooring set up.

Nailer – This can be a hammer or pneumatic nail gun. The pneumatic nail gun is always quicker and easier, but you have to have it calibrated only right so the nails do not go too far down into the wood and ruin your hardwood panels.

Rubber Mallet – This is your chance to pound out your frustrations as you learn how to install hardwood floor. Actually, you should pound them out gently to deliver the surfaces of both panels together perfectly. You don’t want to get them apart or your flooring will possess crevices. But if you pound them too difficult together, you can damage them or push them so far together as to bow them.

Circular Saw – At the end of each row of boards as you go into the corner, you’ll have to cut your floor panels to match. Any fixtures in the room will also need to be trimmed around.

Although the nail down method of installing hardwood flooring panels is pretty simple, it should nevertheless be done carefully since the hardwood flooring must endure for many years in whatever form you finish it.

All the furniture and barriers which can be taken out from the room ought to be eliminated while you install your hardwood floor panels. This is true even if it requires manual dismantling and reassembly. For those fixtures build in the ground of this room, you’ll only need to panel around them. It is not the simplest way to go, but you have to do everything you have to do to get your hardwood floor installed. In case you have door sills, a classic hardwood floor, baseboards, or carpet, remove them before you begin also.

If the surface below where you will be flooring is cement or any other lumpy material, use a felt floor lining to cover this surface. Then put in a plywood sub-floor over it. Once placed, you need to be ready to start installing the hardwood flooring.

Steps on How To Install Hardwood Floor Panels

1. Set your initial floor panel in the corner of this room in which you have decided to start your own flooring. The grooves must be toward the wall and the tongues should be toward the space.

2. Start adding panels to make a row. The last panel should not quite fit right, so you’ll need to utilize that carpenter’s crayon to indicate where to cut it. Use your circular saw to cut it. Be very careful not to cut it too small. The fitting needs to be just about perfect.

3. Use your drill to produce your little pilot holes. Place the nails into secure down your floor. Even though it will take longer, you’ll be thankful when you’re done if you used pilot holes when you are learning how to install hardwood floor.

4. Catch another half of the panel you cut off the row you just finished and utilize it as the starting point for the next row. This will seem strange at first, but when the floor is finished, the counter tops of these boards will look very nice. Additionally, if all your boards paired up, the floor will not have interlocked strength.

5. Continue on doing this as you go through the remaining rows. Utilize the rubber mallet as necessary to create the planks and rows nice and comfortable. When the rubber mallet won’t fit, use the claw hammer to pull on the boards tight. The final things you need are a few giant crevices between your boards when you have finished your hardwood floor.

6. The final panel is the toughest one to get set up, but your flooring will look really awful if you rush at this step.

7. Clean the floor you simply laid.

Cleaning Up After You Install Hardwood Floor Panels

In the process of how to install hardwood floors, cleaning up is overlooked and important enough to warrant its own follow-up section. But unlike other nail method guides about the best way to install hardwood floor panels, we want to make sure you understand this measure.

Cleaning up is important because there are small wood chips and saw dust everywhere after the normal hardwood flooring installation. Use your broom and dust pan to pick up any debris on the ground. These particles, if walked on and rubbed by furniture, can make your brand-new floor seem like a scraped up old floor pretty quickly.

Unless you moved beyond the directions about the best way to install hardwood flooring and used glue in your hardwood panels, then there’s no need to get your flooring wet until it has had a chance to settle. This is because you don’t want it to swell before you have moved the furniture back and given it a couple times to get itself in its closing arrangement.

Special Tips Add-On on How Best to Install Hardwood Floor Panels

Do not get overly aggressive when placing your hardwood floors in place. It’s quite simple to ruin the surface of flooring panels when they’re floating freely and you are placing them and pounding on them. Be particularly cautious when repairing a row that looks a bit off.

If your rubber mallet is hardy enough, it’ll be the best thing to put nails in since it will not do as much damage to the surface of the floor panels.

Your nailed down floor probably is not likely to be as nice as the one installed by an expert. On the other hand, it is going to look pretty nice by itself. It is going to most likely be about the best looking job an inexperienced hardwood floor installer can do. And if you change your mind about the floor, it’s among the simplest hardwood flooring installation approaches to undo.

But apart from being simple to install and uninstall, nailed hardwood floor has some usage benefits over other forms. The most important advantage to keep in mind is that a glued down floor is rigid; once a flooring panel is dried in place, it is there for good whether it’s snug into the next panel over or not. The loose floor isn’t attached to anything and may be creaky, bubbly, and move around. So enjoy your fresh well-fixed hardwood floor.